Hilux 4x4 Forum

Stef

Hi Koos,
Tentoria in Gezina , daar is ook n plek in Zambesi neffens Aldo str...camp-a-tent
In Klerksoord in Topaz park is n plek wat canvas doen ma hulle is effens vol fiemies om custom goed te doen.

Stef

Klink vir my jou vriend het probleme...maar geld is nie een van hulle nie :D: Micro robotics in centurion het 100A DC SSR's vir R199; my probleem is die terminale want ek het 'n 35mm sq kabel na die 2de batt toe om te kan winch met altwee in parallel, maar nou ja...ek het daai winch een keer gebruik...

Stef

Pieta, JA!! Ek het gesien die ouens van planetronics bring hulle in, maar die ou se woorde aan my toe ek vra wat die ding kos was: "as jy n bekostigbare opsie soek is jy nie op die regte plek nie" ek verneem die ding is R6k by hulle. Ek het n vriend wat redelik op dit is wat elektronika e...

Stef

I also need to replace the outer parts of the LTD sliders....one rusted & one bent. The tubes right under the seams hold up very well, it is the "steps" on the outer tubes that that weakens it and also where I bent the one. Thinking of rather having one continuous length with ends bent...

Stef

Nice job :thumbup: Brackets are probably placed to line up with existing holes in the chassis :think: I never had any luck with painting galvanized surfaces, even with all the fancy primers & treatments. Same with aluminium, hence the reason we had the canopies powder coated as it is guaranteed ...

Stef

Moenie dat vroulief j vang werk op die eetkamer tafel nie....

Stef

FIRSTGEER wrote: ↑Sat Dec 16, 2017 7:02 pm Very well done.You can really be proud of a well finnished project and the cherry on top is;- YOU DID IT YOURSELF

+1

Stef

I would also say 4mm2 minimum...2 mil will cause voltage drop

Sent from my S30 using Tapatalk

Stef

Ek al op vd forums gelees dat di ouens sukkel met konneksies op di mag adaptor.
Ma mens weet nooit....skakel dit uit dan weet mens

Sent from my S30 using Tapatalk

Stef

GeorgeJvR wrote: ↑Fri Dec 15, 2017 8:13 am
I'm Looking for one that did not see a panalbeater, and no rust.
Engine; 22R EFI, 4Y EFI , 3RZ, Lexus 2JZ or Lexus v8

En da gaan myne s prys nou net op....

Stef

:thumbup: lekker; ek twyfel of dit die plug is, maar ja, doen hom oor dan weet jy dis reg Al wat ek kan nog kan dink is die mag adaptor. Check alles wat met die trigger te doen het, as daai sein vou dan stop di Dicktator alles. Dalk kan jy die kabel tussen batt - en die starter check as jy se dat da...

Stef

janee dis moeilik....dis hoekom ek so lank gesukkel het want die fout is nooit lank genoeg daar om hom te soek nie. Myne het aan die begin ook so te se dadelik gestart en met tyd alhoe erger geraak. As ek na daai plug kyk dan is +V en -V nie gebruik nie, want daar is net 3 konneksies, coil - , GND e...

Stef

Hallo Stefan, die posbus gat is vêr groter as die gat waar die rollers vir die kabel is. :thumbup: die afstand tussen die winch en die voorste plaat help ook Ek glo 40 grade is genoeg vir A.O.A, hang af hoe erg die hindernisse is wat jy wil ry. Winch is baie mooi in lyn met onderstel as ek na die m...

Stef

+1

There is a crank seal engine side and a seal on the spline shaft gearbox side. If the crank seal has a leak there will be oil accumulating & draining from the bottom of the bell housing

Stef

Lyk goed sover.

Die "posbus" plaat, ek neem aan dis die voorkant waar die kabel deur kom? Is moeilik om te skat op die foto, maar is die opening wyd genoeg, maw dieselfde wydte of wyer as die winch se drom?

Stef

Ag nee Rudi dis mos nou net wat jy nodig het.... Op die Dictator kyk of die oranje LED flikker as jy hom probeer start na hy uitgesny het maw kry jy pulse van die pickup in die dizzy. As j 'n Magnetic pickup het en daar is nie sein nie kyk na jou spasie tussen die pickup en die rotor, moet so klein ...

Stef

Danki oom Dawie, dit is di plan...wil sommer di winch drade ook sort

Sent from my S30 using Tapatalk

Stef

Tx Rudi, also glad it's sorted because it was damn annoying.
Louis told me 'bout the alternator wire, but the one on my bakkie seems to be ok. Still no issues thus far

Stef

Die beste was die "vrag" wat sommer so uit die bak geskiet word as't ware

Verseker 'n gebrek aan goeie oordeel.

Stef

Lekker projek

Hou van die ontwerp

Stef

Hi Thinus,

Kyk bietjie hier:http://www.ledandbeyond.co.za/lights/

Stef

Bliksempie wrote: ↑Wed Dec 06, 2017 12:41 pm Gald nie sleg nie. Dis wat myne ook omtrent gekos het. Ook alles self gedoen

Moet se ek is verbaas dat Alu nie veel duurder as gewone staal is nie

Stef

op die stadium geskat op min R8 000 per canopy, moet nog al die fakture bymekaar tel. Net so rofweg: Cladding is R2600 per sheet en ons het 4 gebruik , dus so R3600 uit die R8k. Slotte skarniere, lifters,rubbers R2500 Powder coating R830 Boute, moere & rivnuts +- R200 3 tubes Soudaflex R250 Alu ...

Stef

:thumbup: Dankie George jy sal moet uithaal want die prys is belaglik :mrgreen: Dink jy nie jy moet een vir 'n V6 vigo bou nie :D: :stir: :surrender: :surrender: :surrender: As jy ernstig is kan ons gesels maar ek moet eerlik wees die materiaal aleen was omtrent die intree prys v die komersiele ekw...

Stef

Bliksempie wrote: ↑Wed Dec 06, 2017 7:02 am Baie netjies Stefan. Het hom laasweek gesien toe jy by Prys uitdeling was (skool). Lyk regtig goed.

Tx Robbie

Het seke nog die oranje stickers op gehad

Moes ma so ry met hom want ek hy is nou ongemaklik om aleen af te haal met die cladding op LOL
Skies ek't jou nie gesien nie..?

Stef

New lifters aren't that expensive either, think we paid R87 each for the 200mm ones gassed to 150Nm, the Mcnaughtans brand that is.

Stef

Boer maak n plan ja

Stef

Dankie

George jy sal moet uithaal want die prys is belaglik

Stef

Stef

I'm pretty sure Gemini has the switch itself as a separate item...but the switch is hardly ever the problem LOL

Have you tried N1 4x4 or Ultimate 4x4?
There is also Wannenburgs & Toyota breakers but I doubt if they'd have.

Stef

Lekker Jan

Also haven't had any issues since bypassing the TP100, but I think I'll still replace the Dicktator with the Spitronics .

Stef

Welkom!

Hele paar ouens het dit al op die IFS Hiluxe gedoen (dis nou die KZTE se shape). Soek vir "Solid Axle Swop"...hier is een vd resultate viewtopic.php?f=8&t=11357&p=126643&hili ... op#p126643

Stef

GeorgeJvR wrote: ↑Mon Nov 06, 2017 7:57 am Gooi bietjie binne fotos asseblief ?

Nee moenie...George gaat jou 'n offer maak!

Stef

Gebruik jy die Dictator se Igniter(Rooi boksie)? Nee die gewone swart chip Gistraand weer begin met sy nonsens toe ek wou ry...sommer die +V & -V direk battery toe gevat, nie eers 'n snik van a dag oud nie. So ek dink ek't hom finaal gewen, maar ek ek is ni lus om geld te spandeer op n nuwe TP1...

Stef

Finally had an opportunity to do proper testing....it failed to start yesterday in the garage and remained in that state for long enough so that i could pry into the harness & hook up my logic tester and a multi-meter. So with ignition on & the Dicktator powered up and no trigger signal.... ...

Stef

What are you running Jan, the original ECU or aftermarket?

Stef

Tx Andy/Dylan,

Most certainly will dyno it again....I believe I'll get better performance with the Spit than the red box

Stef

Where did you mount the ECU? I have the dicktator hidden in the dash but I'm tempted to mount the Spitronic inside the engine bay against the firewall somewhere..

Stef

Looks neat Stef! :thumbup: Any reason why the one has a transverse rip on top while the other two have lateral ribs? Tx Andy. Really pleased with the way it turned out To answer your question...Yes, but it's really just a third arch exactly the same as the front & rear ones with the same latera...

Stef

Ok tx, also got the Saturn. At the same time I got new injector plugs and replaced the coil wires with longer ones from the molex connector. Still waiting for the coil plug and tps plug

Would the standard 4 cyl map start the 22R or should I load something else?

Sent from my S30 using Tapatalk

Stef

Welding all done. Just the finishing, powder coating & final assembly left

Sent from my S30 using Tapatalk

Stef

Jis ma dit het al duur geraak....

Stef

Mud Dog wrote: ↑Wed Oct 18, 2017 11:25 am take it past Mayfair Gearbox and ask their opinion.

I don't have much faith in Mayfair's diagnostic capabilities nor their addiction to silicone....I'm of the opinion that I would have been better off leaving the box as it was. R14k wasted

Stef

"Side" project...

Stef

Which Spitronics model did you get? The Saturn?

Stef

The area of the conductor plays a role i.e you could have a thinner cable with more windings or a thicker one with less windings. That crossing there at the rear could also influence the voltage, but I would suggest to stick one end of the welding cable through the core again in other words add half...

Stef

What I also like about Spitronics is the fact that there is no mag adapter or igniter needed as the drivers are on board

Stef

Thank you Bernhard, There are plenty weird sizes available in Aluminium... :mrgreen: We based our choices on what was available at the local suppliers as places like Huletts would only manufacture on demand with a min qty of 500 lengths IIRC. We opted for 38mm & 32mm square with a 2mm wall; as m...

Stef

Awesome build, really handy when you have something to start with that you can just mold to your needs

Stef

Had the same problem with my Dicktator. Used to cut when I'm at a robot or low revs. Then I had to wait about 20-30 seconds with the power of to get it going again. The exact same symptoms I'm experiencing...and when you get it going I found that one has to rev the engine to about 2000 rpm for a fe...

Stef

First 2 frames now look like this

Stef

Frame #3 all welded together; slightly beefed up with an extra arch and using 3mm wall thickness as this one will have an RTT.
Rear door frames welded together for all 3 frames.

Stef

Hoe kry mens 'n Lexus se consumption reg?....Jy LIEG hom reg :D: KZ Surf's gearbox works just fine on the SFA with its diffs (petrol ratios)...revs more or less the same as what you have. At a stretch it will give 7km/l but tows like a dream. Proper bell housing with normal KZ box, D4D clutch is the...

Stef

Not too much progress made in the last 3 weeks, but in saying that, we are on door design #3, got the cladding & rubbers procured, and some of the cross bars front to back welded in. This week managed to get 4 x door frames cut & welded together; yesterday the flat bar came in so this is wha...

Stef

Tx Louis, sal kyk hoe loop my week

Sent from my S30 using Tapatalk

Stef

Pra' jy oom Dawie, ek is nou al so g@tvol dis nie eers meer snaaks nie...

Stef

I've been told the same thing 5 years ago....maybe its time...I'd rather replace with Sptronics than deal with Dicktator's poor after sales service. MRD racing here in Pta offered to test it for me, so fortunately I won't have to go to Dicktator themselves, maybe they have a loan unit I could use to...

Stef

Right .....completely rebuilt the dizzy with a brand new optic...and it cut out 4 times again tonight. So I guess optic triggers are not as unreliable as most people think as the old one was still fine...that basically leaves the ECU...maybe not as reliable as most believe? Sent from my S30 using Ta...

Stef

OK....so the problem persists, but not as bad as before. A failing battery just highlighted an underlying problem. What still gets me is the trigger line that doesn't go lower than 8V ....thus a slightly flat batt will reduce the signal amplitude. Checked all ground connections, wiring etc. In my mi...

Stef

Eish ...R2500 now...last I checked OME's were just on R2k each. Would have loved the HDPs but didn't have the appetite at the time for over R3k so I got the Safaris.
I'd say go for the HDP's, they are in a different league than the Safaris.

Sent from my S30 using Tapatalk

Search found 2579 matches