3.0 d4d error code

rexx · Post by **rexx** » Mon Mar 11, 2013 7:53 am

Hi ,

I am currently having an issue with my fortuner 3.0 d4d, when accelerating to overtake , with a heavy load( boat) i get the engine fault light coming on and it goes into limp mode, the car runs fine in all other instances, i connected it to my mates diagnostic machine and it gives me p2008 intake mainfold running solenoid , now that intake is quite complex, does anyone know what this solenoid looks like so i can remove and clean it ? Chris

Jaws · Post by **Jaws** » Mon Mar 11, 2013 8:42 am

Do you have a chip installed ?

JEEPIE · Post by **JEEPIE** » Mon Mar 11, 2013 9:02 am

having the same problem on my 2.5 d4d
just normal driving
gonna remoce the chip (plug and play) today to check
keep us updated

rexx · Post by **rexx** » Mon Mar 11, 2013 1:34 pm

Nope no chip that im aware of.

Jaws · Post by **Jaws** » Mon Mar 11, 2013 1:38 pm

P2008 / 58 :
When actual intake air volume detected by MAF meter continues to be smaller than volume estimated from boost pressure and intake air temperature sensor, ECM determines that swirl control valve is stuck closed.
(1 trip detection logic)
Swirl control valve VSV

Open or short in Swirl control valve VSV circuit

Intake manifold (swirl control valve)

EGR valve assembly

MAF meter

ECM

Jaws · Post by **Jaws** » Mon Mar 11, 2013 1:42 pm

rexx wrote:Nope no chip that im aware of.

1. Check the vacuum hose connection of the swirl control valve system.

2. Disconnect the S9 VSV connector.
Measure the resistance of the VSV.
Standard resistance: ( 37 to 44 Ω) @ 20°C

3. Measure the resistance of the IAT sensor.
Standard resistance:
2.21 to 2.69 kΩ @ 20°C
0.49 to 0.67 kΩ @ 60°C

rexx · Post by **rexx** » Mon Mar 11, 2013 1:54 pm

Jeepers... Thanks for all that info, now that throttle body area has like 4 different components. Could you possibly post a picture of the component you are suggesting i test.. Not sure on the exact terminology... Thanks chris

JEEPIE · Post by **JEEPIE** » Mon Mar 11, 2013 4:13 pm

well i removed my chip
so far so good

hope you come right

Jaws · Post by **Jaws** » Mon Mar 11, 2013 5:15 pm

rexx wrote:Jeepers... Thanks for all that info, now that throttle body area has like 4 different components. Could you possibly post a picture of the component you are suggesting i test.. Not sure on the exact terminology... Thanks chris

Where are you Rex ?

rexx · Post by **rexx** » Mon Mar 11, 2013 5:28 pm

Hillcrest, Durban

Jaws · Post by **Jaws** » Mon Mar 11, 2013 7:41 pm

Ok I'll see if I can post a few pics tomorrow

rexx · Post by **rexx** » Thu Mar 14, 2013 9:59 am

Hi Herman,

Any news on those pictures ?

Thanks

Chris

Jaws · Post by **Jaws** » Sat Mar 16, 2013 5:40 pm

Sorry Rex I have been out and about the last few days

J.C Avis · Post by **J.C Avis** » Sun Mar 17, 2013 1:43 am

Ek het met my KZ ombouing n 3.0 D4D engin engin ingesit en die KZ se airfiler box gebruik en die air flow meter in hom gesit,selfde kode uit gegooi en die D4D se air filter box ingesit en als oor,airflow was nie reg gewees nie.

Titos · Post by **Titos** » Sun Mar 17, 2013 11:05 pm

Hi Herman, same problem on my Hliux 3.0 D4D. Any help or pictures to solve this problem will help.

Regards

Thinus

rexx · Post by **rexx** » Thu May 02, 2013 6:34 pm

Hi Gents, So i sent the Fortuner into Toyota today for diagnostics, they found the problem pretty quick , was the airflow sensor, they wanted silly money for a new one, managed to get a second hand one for R400. So instead of costing R2100 it cost me R500 at Toyota for diagnostics and a couple of other bits and bobs and R 400 for the part that literally takes 1 minute to fit..... Car can now pull uphill at 4000 rpm comfortably.

Chris

Post by **hendrik.earle** » Thu May 02, 2013 8:20 pm

My brother-in-law had the same problem on his td4 Land Rover. we just cleaned the airflow sensor (MAF) with electric cleaner and the problem was solved.

lillejon · Post by **lillejon** » Wed May 24, 2023 7:15 am

rexx wrote: ↑Thu May 02, 2013 6:34 pm Hi Gents, So i sent the Fortuner into Toyota today for diagnostics, they found the problem pretty quick , was the airflow sensor, they wanted silly money for a new one, managed to get a second hand one for R400. So instead of costing R2100 it cost me R500 at Toyota for diagnostics and a couple of other bits and bobs and R 400 for the part that literally takes 1 minute to fit..... Car can now pull uphill at 4000 rpm comfortably.

Chris

hi, i see this is old post, but i try anyway, did you have any lamp in your dash? and how did toyota solve this? did they connect the diagnostic on the car and drove a trip with a trailer or did they just connect and figure it out when the car was parking?
i have the same problem, on my car the vacuumhose is ok, the vavuumclock works when i use vacuum directly on the clock,
when i connect my universial diagnostictool i get som valvue from the airflowsensor, but not sure if the is correct valvue.
regards

Hilux 4x4 Forum

3.0 d4d error code

3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code

Re: 3.0 d4d error code