Does the SFA powersteering gearbox take any oil?
In the manual it is evident that the non-powersteering box takes gear oil but nowhere does it mention the requirement of any gear oil for the powersteering box or the packing of grease during assembly, neither can I see any evidence of a filler plug on mine. Does the powersteering A/T fluid run through the entire box and lubricate it by any chance? Mine is as pictured below:
YOU wrote:Does the power steering A/T fluid run through the entire box and lubricate it by any chance?
Yep.
When your road comes to an end ...... you need a HILUX!.
Life is like a jar of Jalapeño peppers ... what you do today, might burn your ass tomorrow. Don't take life too seriously ..... no-one gets out alive. It's not about waiting for storms to pass. It's about learning to dance in the rain. And be yourself ..... everyone else is taken!
Nah just slowly replacing all fluids etc. No leaks, if it aint broke, don't fix it haha.
Luke what is your carby setup now? I think I saw on Faceboet that you are running a Weber?
Why so if your Aisin was also getting 8km/l with the modification to it?
I've used Castrol for a long time without any issues. I also use it in my hydraulic jacks so buy 5lit at a time ... not too pricey either.
When your road comes to an end ...... you need a HILUX!.
Life is like a jar of Jalapeño peppers ... what you do today, might burn your ass tomorrow. Don't take life too seriously ..... no-one gets out alive. It's not about waiting for storms to pass. It's about learning to dance in the rain. And be yourself ..... everyone else is taken!
Tim86 wrote: ↑Tue Oct 09, 2018 8:49 am
Nah just slowly replacing all fluids etc. No leaks, if it aint broke, don't fix it haha.
Luke what is your carby setup now? I think I saw on Faceboet that you are running a Weber?
Why so if your Aisin was also getting 8km/l with the modification to it?
Currently I am running a weber 32/36. The Aisin I had on had the carburettor enhancer setup on it and it was ok on the open road but it was not idling well at all, I had it rebuilt by a reputable shop and even after they replace all jets and checked it out it still ran like crap. Realistically now I am getting 7.8km/l on the open road and about 6.5km/l in town if I don't drive like a taxi. Its my daily driver so I am sure about the mileage. And after the timing chain rebuild it runs soooo much better.
With each replacement of parts, a car slowly becomes Chinese.
Do you think the carby enhancer caused it to idle poorly or was it merely the carb itself?
I haven't got to it yet but I plan on running the enhancer vacuum line into the cab with the needle valve on the dash so I can tune it, mark the setting and then easily flip it off for town/stop-start driving (smoother idling...?) and on for the lang pad. Have you considered implementing the enhancer on your new Weber?
Agree wholeheartedly - new chain is a win in all respects.
Do you also have the Brospeed cam and what is your timing set at?
Do you think the carby enhancer caused it to idle poorly or was it merely the carb itself? With the Carb enhancer connected and disconnected it still ran badly, I have a video actually where you can hear it coughing and spitting through the exhaust. I am not sure what it was to be honest, all I know is after we installed the Weber it was a whole different machine, smoother more power and muuuch more economical. At worst the carb enhancer gave it a slight dead spot as you take off, but the manual does say it will do that.
I haven't got to it yet but I plan on running the enhancer vacuum line into the cab with the needle valve on the dash so I can tune it, mark the setting and then easily flip it off for town/stop-start driving (smoother idling...?) and on for the lang pad. Please let us know how it works out for you.
Have you considered implementing the enhancer on your new Weber? Most definitly, I wanted to get the bakkie back to normal runing condition and already with the new vacuum advance and weber i am getting the above mileage.
Agree wholeheartedly - new chain is a win in all respects.
Do you also have the Brospeed cam and what is your timing set at? I actually shelved the cam for a standard cam like mud dog did with his Hilux. I am running standard timing specs at the moment.
With each replacement of parts, a car slowly becomes Chinese.
