Page 1 of 1
Odd Request
Posted: Fri May 29, 2015 9:14 am
by WayneSchalk
I need some help, I have a steel table that we want to use in doors, the thing is we had to cut the legs off as it did not go through the door.
To put the legs back on I was thinking of using a smaller diameter pipe inside the pipe of the leg, that way I can rivet it in the one side so that I can take the legs off to move it in future.
But it seems like I cannot get the size that easily. I need a pipe with an outside diameter of 38mm. I need 4 x 100mm
is there anyone with access to a lathe that can machine it for me?
Re: Odd Request
Posted: Fri May 29, 2015 10:01 am
by Haboob
Wayne, Have you checked the exhaust places, I'm sure they have 38mm pipes...
Re: Odd Request
Posted: Fri May 29, 2015 10:33 am
by WayneSchalk
Haboob wrote:Wayne, Have you checked the exhaust places, I'm sure they have 38mm pipes...
Good idea, I'll go have a look
Re: Odd Request
Posted: Fri May 29, 2015 12:26 pm
by Thabogrobler
Square or round?
Re: Odd Request
Posted: Fri May 29, 2015 12:38 pm
by Mud Dog
If you can't find a size that fits inside, how about one that fits over?
Re: Odd Request
Posted: Fri May 29, 2015 1:22 pm
by WayneSchalk
Thabogrobler wrote:Square or round?
Round
Re: Odd Request
Posted: Fri May 29, 2015 1:23 pm
by WayneSchalk
Mud Dog wrote:If you can't find a size that fits inside, how about one that fits over?
for one that goes over I will need a pipe with an inside diameter of 44mm, any will do, but I think one for inside will be easier to get.
Re: Odd Request
Posted: Fri May 29, 2015 2:45 pm
by Rianc
Moet dit staal wees? Maak dit bietjie abstrak en draai jou pote uit mooi hout volgens grote eg tambotie, geelhout of selfs kiaat? Net 'n gedagte.
Re: Odd Request
Posted: Fri May 29, 2015 2:53 pm
by Obelix and Dogmatix
Thabogrobler wrote:Square or round?
Waar koop jy square pyp Thabo? hoop nie jy gebruik daai square pyp op jou site nie :evil: :evil: :roll:
Re: Odd Request
Posted: Fri May 29, 2015 2:54 pm
by WayneSchalk
Rianc wrote:Moet dit staal wees? Maak dit bietjie abstrak en draai jou pote uit mooi hout volgens grote eg tambotie, geelhout of selfs kiaat? Net 'n gedagte.
Dit kan seker doen, ek het maar net nie toegang tot 'n draaibank nie.
Re: Odd Request
Posted: Fri May 29, 2015 8:06 pm
by SYRON CONVERSIONS
just get the exhaust guys to flare the end larger
Re: Odd Request
Posted: Fri May 29, 2015 8:47 pm
by Froll
Take a piece of pipe the same size the length that you need. Cut a small piece out through the length and close it a bit in a vice. Perfect fit every time.
Re: Odd Request
Posted: Mon Jun 01, 2015 9:55 am
by Stef
I would just weld them back on, unless you're moving it around often...
Re: Odd Request
Posted: Mon Jun 01, 2015 5:12 pm
by Scott
just have the legs you cut off crimped at a exhaust place.
Re: Odd Request
Posted: Mon Jun 01, 2015 6:39 pm
by legend35
Froll wrote:Take a piece of pipe the same size the length that you need. Cut a small piece out through the length and close it a bit in a vice. Perfect fit every time.
Best idea.I would do that